ADIC DLT 7000 Spécifications Page 29
- Page / 68
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Hardware Installation 13
Installing the SCSI Cable and Terminator
Notes
Make sure that the interface cable you are planning on using has the appropriate connectors on each end. The FastStor
employs a 68-pin high-density SCSI connector on the rear panel.
If your host computer’s SCSI connector is different from that on the FastStor, you will need to obtain an adapter or a
different cable. Consult your dealer or ATAC if you need help.
The interface cable must be shielded – ADIC can supply you with the correct type.
❐ If your FastStor is the last device on the SCSI bus, install the SCSI terminator onto the remaining SCSI connector on the rear
panel of the FastStor.
Note
SCSI bus TERM POWER is supplied by the robotics interface, not by the drive.
❐ Connect the SCSI cable to either of the SCSI connectors on the rear panel of the FastStor.
SCSI Terminator
SCSI Cable
FastStor Rear Panel
❐ Connect the free end of the SCSI cable to the connector on the host computer’s SCSI adapter.
❐ If you wish to connect one or more additional devices to the bus after the FastStor, connect an appropriate cable between the
remaining SCSI connector on the rear panel of the FastStor and the next device.
❐ Be sure that the bus is terminated at the last device in the chain.
Note
ADIC recommends that you always terminate a single-ended SCSI bus with an active terminator.
✔ Make sure that the SCSI cable between the host adapter and the FastStor is secure and the connections are fastened correctly.
- FastStor 1
- Copyright Notice 2
- Copyright Notice (Europe) 3
- Regulatory Notices 4
- CE Notice 5
- VCCI Notices (Japan Only) 5
- Safety Notices 7
- Table of Contents 9
- Quick Start Guide 11
- Blank Page 16
- Chapter 17
- Equipment Description 18
- Features 19
- DLT Drives 20
- Options 20
- Switches and Indicators 21
- L r rea y 23
- DLT Media 25
- Other Requirements 26
- Unpacking and Inspecting 28
- Installing the Host Adapter 28
- SCSI Terminator 29
- SCSI Cable 29
- Normal Operations 32
- L r init 33
- Drive Status Messages 36
- FastStor Modes 37
- Loa rv 38
- SRC slot 38
- SRC slot N 40
- SRC slot n 41
- EJECT PCKR 42
- DENSITY 43
- Set scsi 44
- L r scsi 44
- L r I x 45
- Cycle pwr 45
- Normal Maintenance 46
- Cleaning the Enclosure 48
- Installation Problems 50
- DIAGNOSTIC MENU 50
- DISPLAY FIRMWARE 51
- Sign on 54
- Chg mo e 55
- Cycle TEST 56
- CycleS 56
- CLEAN RV 56
- Ct 2 (Sel) 57
- Cleaning 57
- RMV 2 (Sel) 57
- AUTOCLEAN 58
- CT 2 (SEL) 58
- CYCLE AC 59
- RMV 2 (SEL) 60
- SP cOUNTS 60
- (000000XX) 62
- UPG rv fw 62
- Ct 2 (sel) 62
- Rmv 2 (sel) 63
- FastStor Error Messages 64
- Environmental Considerations 65
- Appendix 67
Approx APPKBM manuales
Manuales del propietario y guías del usuario para Teclados Approx APPKBM.
Ofrecemos 1 manuales en pdf Approx APPKBM para descargar gratis por tipos de documentos: Guía de usuario
Commentaires sur ces manuels